Delta 46-755X Manuel d'utilisateur télécharger pdf (Page 4)

ADDITIONAL SAFETY RULES FOR

WOOD LATHES

1. DO NOT OPERATE THIS MACHINE UNTIL it is

assembled and installed according to the instruc-

tions.

2. OBTAIN ADVICE from your supervisor, instruc-

tor, or another qualified person if you are not

familiar with the operation of this machine.

3. FOLLOW ALL WIRING CODES and recommend-

ed electrical connections.

4. ROUGH CUT THE WORKPIECE as close as pos-

sible to the finished shape before installing it on the

faceplate.

5. EXAMINE THE WORKPIECE FOR FLAWS and

test glue joints before mounting the workpiece on

machine. DO NOT mount a split workpiece or one

containing a knot.

6. SECURELY FASTEN THE WORKPIECE to the

faceplate prior to faceplate turning. Use the appro-

priate size faceplate to properly support the work-

piece. Do not let the screw fasteners interfere with

the turning tool at the finished dimension of the

workpiece.

7. NEVER DRIVE THE WORKPIECE into the drive

center while the drive center is in the headstock.

Set the drive center into the workpiece with a soft

mallet prior to installing it on the headstock.

8. SNUG THE TAILSTOCK CENTER against the

workpiece and lock it. Lubricate the tailstock cen-

ter if it is not a ball bearing center.

9. PROPERLY ADJUST THE TOOL REST HEIGHT.

10. ADJUST THE TOOL REST so it is as close to the

workpiece as possible.

11. TIGHTEN ALL CLAMP LOCKING HANDLES

before operating.

12. ROTATE THE WORKPIECE BY HAND to check

clearance before turning the machine “ON”.

13. CLEAR THE LATHE BED OF ALL OBJECTS

(tools, scraps of wood, etc.) before turning the

machine “ON”.

14. EXAMINE THE SET-UP CAREFULLY before turning

the machine “ON”.

15. STAND CLEAR, AND KEEP ALL OBSERVERS

AND PASSERSBY clear of rotating path of work-

piece to avoid injury from flying debris.

16. USE THE LOWEST SPEED when starting a new

workpiece. NEVER EXCEED recommended

speeds.

17. NEVER ADJUST THE TOOL REST while the work-

piece is turning.

18. NEVER LOOSEN THE TAILSTOCK SPINDLE or

the tailstock while workpiece is turning.

19. MOVE THE CUTTING TOOL INTO THE WORK-

PIECE SLOWLY, and cut small amounts when

roughing.

20. REMOVE THE TOOL REST before sanding or pol-

ishing.

21. NEVER PERFORM LAYOUT, assembly, or set-up

work on the table/work area when the machine is

running.

22. TURN THE MACHINE “OFF” AND DISCONNECT

THE MACHINE from the power source before

installing or removing accessories, before adjusting

or changing set-ups, or when making repairs.

23. TURN THE MACHINE “OFF”, disconnect the

machine from the power source, and clean the

table/work area before leaving the machine. LOCK

THE SWITCH IN THE “OFF” POSITION to pre-

vent unauthorized use.

24. ADDITIONAL INFORMATION regarding the safe

and proper operation of power tools (i.e. a safety

video) is available from the Power Tool Institute,

1300 Sumner Avenue, Cleveland, OH 44115-2851

(www.powertoolinstitute.com). Information is also

available from the National Safety Council, 1121

Spring Lake Drive, Itasca, IL 60143-3201. Please

refer to the American National Standards Institute

ANSI 01.1 Safety Requirements for Woodworking

Machines and the U.S. Department of Labor

OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.

1 2 3 4 5 6 7 8 9 ... 23 24

Commentaires sur ces manuels

Pas de commentaire

Delta 46-755X Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Delta 46-755X