Delta AH500 series Manuel Page 263
- Page / 297
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 8 Maintenance and Inspection
8.2.2
Daily Inspection
No. Item Inspection Criterion Remedy
1 Appearance Check visually.
Dirt must not be
present.
Remove the dirt.
Check whether the set
screws are loose.
Further tighten the
screws.
2
Installation of a
backplane
Check whether the
backplane is installed on
the DIN rail properly.
The backplane must
be installed firmly.
Install the
backplane on the
DIN rail properly.
3 Installation of a module
Check whether the
module is loose, the
projection is inserted into
the hole on the backplane,
and the screw is
tightened.
The projection under
the module must be
inserted into the hole
in the backplane, and
the screw must be
tightened.
Install the module
firmly.
Check whether the
removable terminal block
is loose.
The removable
terminal block must
not be loose.
Install the terminal
block firmly.
4 Connection
Check whether the
connector is loose.
The connector must
not be loose.
Further tighten the
screws on the
connector.
Power
supply
module
POWER
LED
indicator
Check whether the
POWER LED indicator is
ON.
The POWER LED
indicator must be ON.
RUN LED
indicator
When the CPU module is
running, check whether
the RUN LED is ON.
The RUN LED
indicator must be ON.
ERROR LED
indicator
Check whether the
ERROR LED indicator is
OFF.
The ERROR LED
indicator must be OFF.
BUS FAULT
LED
indicator
Check whether the BUS
FAULT LED indicator is
OFF.
The BUS FAULT LED
indicator must be OFF.
CPU
module
SYSTEM
LED
indicator
Check whether the
SYSTEM LED indicator is
OFF.
The SYSTEM LED
indicator must be OFF.
5
LED indicators on an
extension module
Check whether the LED
indicators on the
extension module are ON.
If the LED indicators
are ON, the module
operates normally.
Please refer to
chapter 9 for more
information about
the
troubleshooting.
* Please refer to Module Manual for more information related to the LED indicators on the extension modules.
8.3 Periodic Maintenance
Under the condition that the daily inspection is undertaken, users are suggested that they should carry out the
periodic maintenance according to the actual operating environment. After making sure that the ambient
environment and the AH500 system conform to the cautions listed in section 8.1, users then can undertake the
periodic inspection described below. If any abnormal situation occurs, please follow the remedy and carry out
the maintenance.
8-3
- Hardware Manual 1
- Hardware Manual 1
- Table of Contents 11
- 1.1 Overview 12
- 1.2 Characteristics 18
- CPU530-RS2 21
- Main backplane 28
- Power supply module 29
- 29
- CPU module 29
- Communication cable 30
- 2.1.1.2 Accessories 30
- Extension module 30
- Extension backplane 34
- Main backplane as a RTU 34
- 2.2 Warning 35
- 2.3 Installation 36
- Installing a DIN rail 37
- Removing a DIN rail 38
- 2.3.3 Installing a Module 39
- Installation 40
- Removal 40
- 2.3.6 Connecting Backplanes 42
- Main backplan 43
- Extension backplane 43
- 3.1 General Specifications 46
- 3.2.2 Profiles 48
- 3.2.3 Dimensions 49
- CPU530-EN 50
- 3.3.2 Profiles 51
- 3.3.3 Dimensions 53
- 3.4.2 Profile 56
- 3.4.3 Dimensions 57
- 120/240 V AC 60
- 0.5 A/output 60
- (2 A/COM) 60
- 3.5.2 Profiles 62
- 24VDC 5mA 63
- 12~24VDC 0.1A 64
- 39 4039 40 67
- 12~24VDC 0.5A 69
- 32A 02NP 70
- 64AM 10N 71
- 98110 11 12 13 14 5 74
- DVPAETB-OT32B 80
- GND +24V 81
- GND +24V 82
- Analog-to-digital 84
- Digital-to-analog 88
- 3.6.2 Profiles 89
- 3.6.3 Dimensions 90
- -10~+10V 91
- -20~+20mA 91
- ±10V,±20mA 92
- ±10V,0/4~20mA 92
- 3.7.2 Profiles 94
- 3.7.3 Dimensions 96
- RTD 2/3/4-WIRE 97
- 3.8.2 Profiles 101
- Ethernet 102
- Points for attention: 103
- Profibus 104
- 1. PROFIBUS-DP port 105
- NODE ADDRESS 107
- 3.8.3 Dimensions 108
- Et hern et 109
- Node Address 110
- 3.9.2 Profiles 124
- Micro SD 127
- 20MC20MC 129
- 3.9.3 Dimensions 131
- 3.10.2 Profiles 141
- 3.10.3 Dimensions 143
- NodeAddress 144
- 3.11.2 Profiles 145
- AHAADP01EF-5A 146
- AHAADP02EF-5A 146
- 4.1 Assigning I/O Addresses 150
- 4.3 User-defined Addresses 154
- AH500 Hardware Manual 158
- Chapter 5 Wiring 159
- 5.1 Wiring 161
- 5.2 Connecting Power Cables 162
- AC power supply 163
- 100-240V 163
- 100~240V 164
- AHPS05-5A 165
- 5.2.4 Power Consumption 166
- 5.3 Wiring CPU Modules 168
- 5.4.1 Wiring AH16AM10N-5A 169
- 5.4.2 Wiring AH16AM30N-5A 170
- 5.4.3 Wiring AH16AR10N-5A 171
- 5.4.4 Wiring AH16AN01S-5A 172
- 5.4.5 Wiring AH16AN01R-5A 173
- 5.4.6 Wiring AH16AN01T-5A 174
- 5.4.7 Wiring AH16AN01P-5A 175
- 5.4.8 Wiring AH16AP11R-5A 176
- 5.4.9 Wiring AH16AP11T-5A 177
- 5.4.10 Wiring AH16AP11P-5A 178
- 5.4.11 Wiring AH32AM10N-5A 179
- 5.4.12 Wiring AH32AM10N-5B 180
- 5.4.13 Wiring AH32AM10N-5C 181
- 5.4.14 Wiring AH32AN02T-5A 182
- 5.4.15 Wiring AH32AN02T-5B 183
- 5.4.16 Wiring AH32AN02T-5C 184
- 5.4.17 Wiring AH32AN02P-5A 186
- 5.4.18 Wiring AH32AN02P-5B 187
- 5.4.19 Wiring AH32AN02P-5C 188
- 5.4.20 Wiring AH64AM10N-5C 190
- 5.4.21 Wiring AH64AN02T-5C 191
- 5.4.22 Wiring AH64AN02P-5C 192
- 5.5.1.2 Relay Type 194
- Sinking 194
- Two-wire proximit 195
- Optoelectronic switch 196
- 5.5.2.1 Output Circuits 197
- Contact Current(A) 198
- DC power supply 200
- D: 1N4001 diode 200
- 5.6.1 Wiring AH04AD-5A 203
- 5.6.2 Wiring AH08AD-5B 204
- 5.6.3 Wiring AH08AD-5C 204
- 5.6.4 Wiring AH04DA-5A 205
- 5.6.5 Wiring AH08DA-5B 206
- 5.6.6 Wiring AH08DA-5C 207
- 5.6.7 Wiring AH06XA-5A 208
- 5.7.1 Wiring AH04PT-5A 209
- 5.7.2 Wiring AH08PTG-5A 210
- 5.8 Wiring Network Modules 211
- Shielded cabl 212
- 5.8.2 Wiring AH10EN-5A 213
- 5.8.3 Wiring AH10SCM-5A 213
- DP Port 214
- Function Switch 216
- 5.9.1 Wiring AHRTU-DNET-5A 216
- 5.9.2 Wiring AHRTU-PFBS-5A 218
- 5.10.3.1 External Wiring 235
- Encoder output 236
- H04HC-5A high-speed input 236
- Transistor output 237
- AH04HC-5A 237
- Terminals on AH05PM-5A 238
- Connector on AH10PM-5A 239
- Connector on AH15PM-5A 240
- Sinking 241
- Sourcing 241
- (24 V sinking) 242
- AC servo drive 244
- Chapter 5 Wiring 246
- 5.10.5 Wiring AH20MC-5A 250
- Chapter 6 Memory Card 253
- SD card families 254
- AHCPU500/510/520/530-RS2 255
- AHCPU500/510/520/530-EN 255
- Write-protected 255
- Chapter 7 EMC Standards 257
- 7.1.3 Cables 259
- 8.1 Cautions 262
- 8.2 Daily Maintenance 262
- 8.3 Periodic Maintenance 263
- Chapter 9 Troubleshooting 265
- Measurement Modules 285
- 1. AH10PFBS-5A has not 295
- 2. PROFIBUS-DP master 295
- Chapter 9 Troubleshooting 297
Produits connexes et manuels pour Matériel d'enregistrement Delta AH500 series
(32 pages)
(42 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.330 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels