Delta MMC120 Manuel d'utilisateur Page 119
- Page / 150
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
119
AUTO STOP
Default: 0x1FE0 (Soft Stops enabled, Hard Stops enabled for Transducer
Errors)
Click here for the AUTO STOP Bit Map
The Auto Stop parameter controls the action taken on the rising edge of any of the eight
(8) most-significant bits in the Status word, which are all fault bits:
Fault Status Bit
7 15 - No Transducer
6 14 - Transducer Noise
5 13 - Transducer Overflow
4 12 - Overdrive
3 11 - Parameter Error
2 10 - Pos./Press. Overflow
1 9-IntegratorWindup
0 8 - Following Error
The available actions for each fault are listed below:
• Status Only
The fault will be reflected in its corresponding status bit in the Status word, but no
further action will be taken. This option is not available for the following faults: No
Transducer, Transducer Overflow, and Transducer Noise.
• Soft Stop
The fault will trigger ramping the axis to a stop. If the axis is in closed loop, the
speed will ramp down to zero using the current Deceleration value. If the axis is in
open loop, then the drive will be ramped down to zero at a rate of 100 mV per
millisecond. If there is an event sequence on the axis, it will stop executing. The
Halt status bit will also be set in the Status word. Some faults will use the open loop
ramp down even if the axis was in closed loop: Position Overflow, No Transducer,
Transducer Overflow, and Transducer Noise. This is done because we cannot count
on the positions being correct, and therefore cannot maintain closed loop control.
• Hard Stop
The fault will trigger the drive output going immediately to 0 mV. The axis will be
placed in open loop mode, and will stay there until a new command is issued. If there
is an event sequence on the axis, it will stop executing. The Halt and Open Loop
status bit will also be set in the Status word.
To view or change the Auto Stop parameter value, open the Auto Stop popup editor using
one of the methods described in Using Popup Editors. Select the desired action for each
fault type and click OK. Changes to this parameter do not take effect until you issue a
Set Parameters (P) command.
Manual Parameter Entry
This parameter can also be edited manually, but this is discouraged since it is much easier
- DCS120-Win Software 1
- User Manual 1
- Table of Contents 2
- Introducing the MMC120 7
- MMC120 Overview 7
- Disclaimer 7
- Principle of Operation 9
- Starting Up the MMC120 11
- Step-by-Step MMC120 Startup 11
- Setup Details 15
- Using DCS120-Win 20
- DCS120-Win Overview 20
- Screen Layout 21
- Command area 22
- Parameter area 23
- Plot Time area 24
- Status area 24
- Status Bar 24
- Basic Topics 26
- Read-back versus Write Mode 27
- Using Popup Editors 28
- Using the STATUS Bits Window 28
- Using the Command Log 29
- Using Stored Commands 31
- Setup Options 32
- Using Multiple Motion Modules 33
- Creating a New Board File 33
- Changing Between Board Files 34
- Using Plots 37
- Selecting the Data to Plot 38
- Using the Plot Detail Window 38
- Viewing the Raw Plot Data 39
- Saving and Restoring Plots 40
- Printing a Plot 40
- Plot Time 41
- Table Editors 42
- Editing the Profile Table 44
- Editing the Event Step Table 44
- Advanced Topics 47
- Forcing Initialization 48
- Using Look-only Mode 48
- Using PC Mode 48
- Command Line Options 49
- Options Dialog Box 50
- Controller Features 51
- Event Control Overview 51
- FLASH Memory 53
- LED Indicators 54
- Motion Profiles 55
- Synchronizing Axes 57
- Two per unit 60
- Communicating with the MMC120 61
- Input Register Overview 63
- Output Register Overview 64
- 1514131211109876543210 65
- SAR Type Index 65
- Support and Troubleshooting 66
- Warranty 66
- Troubleshooting 66
- Error Handling 67
- MMC120 Module Problems 67
- Hydraulic System Problems 69
- Technical Support 73
- Parameter Errors 74
- Invalid command received 76
- Appendix A: Command Reference 78
- General ASCII Commands 78
- Start Events Command 79
- Set Feed Forward Command 79
- Go Command 79
- Halt Command 80
- Set Integral Drive Command 80
- Relative Move Command 81
- Disable Drive Output Command 81
- Set Mode Command 82
- Set Null Drive Command 82
- Open Loop Command 82
- Set Parameters Command 84
- Quit Events Command 84
- Restore Null Drive Command 84
- Save Null Drive Command 85
- Save Integral Drive Command 85
- Update FLASH Command 85
- Set Speed (Unsigned) Command 86
- Set Speed (Signed) Command 86
- Start a Graph Command 86
- Go Using Profile Commands 87
- Set Profile Commands 88
- Set Parameter Commands 90
- ASCII Commands 91
- Get Profile Commands 93
- 0xAC-0xAF 37 94
- Get Parameter Commands 95
- Event Step Edit Commands 97
- LINK TYPE/NEXT 98
- Diagnostics Command 98
- Event Step Transfer Command 99
- MODE Word Bit Map 103
- ACCELERATION 104
- DECELERATION 104
- COMMAND VALUE 105
- Command Field 106
- CONFIGURATION Word 107
- CONFIGURATION Word Bit Map 109
- SCALE Calculation Examples 111
- EXTEND LIMIT 112
- RETRACT LIMIT 113
- PROPORTIONAL GAIN 113
- INTEGRAL GAIN 114
- DIFFERENTIAL GAIN 115
- EXTEND FEED FORWARD 115
- RETRACT FEED FORWARD 116
- DEAD BAND ELIMINATOR 117
- IN POSITION 118
- FOLLOWING ERROR 118
- AUTO STOP 119
- AUTO STOP Bit Map 120
- Valid 16-Bit Positions 121
- COMMAND POSITION 122
- TARGET POSITION 123
- ACTUAL POSITION 123
- TRANSDUCER COUNTS 124
- AXIS STATUS Word 124
- STATUS Word Bit Map 128
- ACTUAL SPEED 129
- NULL DRIVE 130
- LINK VALUE 130
- Link Types and Link Values 130
- Link Next 131
- System-wide Link Types 132
- Current Axis Link Types 132
- Link Type and Link Value 133
- Selected Axis Link Types 135
- Link Type - Any Axis Speed 136
- MMC120 Specifications 138
- Appendix G: Glossary 139
- Glossary 139
Produits connexes et manuels pour Capteurs Delta MMC120
Capteurs Delta MMC120 Manuel d'utilisateur
(105 pages)
(105 pages)
Fluke 9140 Dry-well Calibrator Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Ausrüstung Fluke 9140 Dry-well Calibrator.
Wir stellen 1 PDF-Handbücher Fluke 9140 Dry-well Calibrator zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels