Delta 50-860 Spécifications télécharger pdf (Page 3)

IMPORTANT SAFETY RULES

As with all machinery there are cert ain hazards involved with operation and use of the machine. Using the machine with

respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are

overlooked or ignored, personal injury to the operator may result.

This machine was designed for cert ain applications only . Delt a Machinery strongly recommends that this machine

N O T be modified and/or used for any application other than that for which it was designed. If you have any questions rel -

ative to it s application, DO N O T use the machine until you have first cont acted Delt a Machinery and we have advised you.

Technical Service Manager

Delt a Machinery

4825 Highway 45 North

P.O. Box 2468

Jackson, TN 38302-2468

(IN CANADA: 505 SOUTHGATE DRIVE, GUELPH, ONTARIO N1H 6M7)

W ARNING: FAILURE TO FOLLOW THESE RULES

M AY RESULT IN SERIOUS PERSONAL INJURY

1. FOR YOUR O W N SAFETY, READ INSTRUCTION

MANUAL BEFORE OPERATING THE TO O L. Learn the

tool s application and limit ations as well as the specific

hazards peculiar to it.

2. KEEP GUARDS IN PLACE and in working order.

3. ALWAYSWEAREYEPROTECTION.

4. GROUND ALLTOOLS. If tool is equipped with three-

prong plug, it should be plugged into a three-hole electrical

recept acle. If an adapter is used to accommodate a two-

prong recept acle, the adapter lug must be att ached to a

known ground. Never remove the third prong.

5. REMOVE ADJUSTING KEYS AND WRENCHES.

Form habit of checking to see that keys and adjusting

wrenches are removed from tool before turning it on.

6. KEEP WORKAREA CLEAN. Cluttered areas and

benches invite accident s.

7. DON T USE IN DANGEROUS ENVIRONMENT. Don t

use power tools in damp or wet locations, or expose them

to rain. Keep work area well-lighted.

8. KEEP CHILDREN A N D VISITO R S A W A Y . All children

and visitors should be kept a safe dist ance from work area.

9. MAKEWORKSHOP CHILDPROOF with p adlocks,

master switches, or by removing st arter keys.

10. DON T FORCE TO O L. It will do the job better and be

safer at the rate for which it was designed.

11. U SE RIGHT TO O L. Don t force tool or att achment to do

a job for which it was not designed.

12. WEARPROPER APPAREL. No loose clothing, gloves,

neckties, rings, bracelet s, or other jewelry to get caught in

moving part s. Nonslip footwear is recommended. Wear

protective hair covering to cont ain long hair .

13. ALW AYS USE SAFETY GLASSES.W ear safety glasse

(must comply with ANSI Z87.1). Everyday eyeglasses only

have impact resist ant lenses; they are not safety glasses.

Also use face or dust mask if cutting operation is dusty.

14. SECURE WORK. Use clamp s or a vise to hold work

when practical. It s safer than using your hand and frees

both hands to operate tool.

15. DON T OVERREACH. Keep proper footing and bal -

ance at all times.

16. MAINTAIN TOOLS IN TOP CONDITION. Keep tools

sharp and clean for best and safest performance. Follow

instructions for lubricating and changing accessories.

17. DISCONNECT TOOLS before servicing and when

changing accessories such as blades, bit s, cutters, etc.

18. USE RECOMMENDED ACCESSORIES. The use of

accessories and att achments not recommended by Delt a

may cause hazards or risk of injury to persons.

19. AVOID ACCIDENTAL STARTING. Make sure switch is

in OFF position before plugging in power cord.

20. NEVER STAND O N TOOL. Serious injury could occur

if the tool is tipped or if the cutting tool is accident ally

cont acted.

21. CHECK DAMAGED PARTS. Before further use of the

tool, a guard or other p art that is damaged should be care -

fully checked to ensure that it will operate properly and

perform it s intended function check for alignment of mov -

ing p art s, binding of moving p art s, breakage of p art s, mount -

ing, and any other conditions that may af fect its

operation. A guard or other p art that is damaged should be

properly rep aired or replaced.

22. DIRECTION O F FEED. Feed work into a blade or

cutter against the direction of rot ation of the blade or cutter

only.

23. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN

POWEROFF. Dont leave tool until it comes to a complete

stop.

24. DRUGS, ALCOHOL, MEDICATION. Do not operate

tool while under the influence of drugs, alcohol or any

medication.

25. MAKE SURE TOOL IS DISCONNECTED FR OM

POWERSUPPLY while motor is being mounted, connected

or reconnected.

26. W ARNING: The dust generated by cert ain woods and

wood products can be injurious to your health. Always

operate machinery in well ventilated areas and provide for

proper dust removal. Use wood dust collection systems

whenever possible.

1 2 3 4 5 6 7 8 ... 11 12

Commentaires sur ces manuels

Pas de commentaire

Delta 50-860 Spécifications Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Delta 50-860