Delta JT160 Manuel d'instructions Page 1

INSTRUCTION MANUALDJ-20 8" Jointer(Model 37-365X, 37-680 and 37-680X)PART NO. A06586 - 08-23-04Copyright © 2004 Delta MachineryTo learn more abou

10Fig. 5ATHE JOINTER IS EXTREMELY HEAVY. HAVE TWO OR MORE PEOPLE HELP LIFT AND MOVEMACHINE AROUND DURING ASSEMBLY.EBBFig. 4BInfeed TableOutfeed TableJ

11ASSEMBLING MOTOR PULLEYAssemble motor pulley (K) Fig. 7A, to motor shaft withthe hub of the pulley in the outer position as shown.Make certain key (

12ASSEMBLING FENCECARRIAGE ASSEMBLY1. Remove the two M10x1.5x30mm hex socket headscrews (A) Fig. 11, and 10mm flat washers from theback of the jointer

13ASSEMBLINGCUTTERHEAD GUARDLoosen set screw (A) Fig. 16. Insert post (B) of thecutterhead guard into hole in infeed table and tighten setscrew (A) ag

14OPERATIONSTARTING AND STOPPING JOINTERTo turn the machine “ON”, push the green start button(A) Fig. 17. To turn the machine “OFF”, push the redstop

15Fig. 19INFEED TABLEADJUSTMENTSTo raise or lower the infeed table (see Fig. 4A), loosentable lock handle (A) Fig. 19, and move the table raisingand l

16KNIFE ADJUSTMENTSIn order to do accurate work, the knives must be exactlylevel with the outfeed table. To check and adjust,proceed as follows:DISCON

17FENCE OPERATIONThe fence can be moved across the table by looseninglock lever (A) Fig. 30, move the fence to the desiredposition, and tighten lock l

18Fig. 342. Using a square (D) Fig. 34, check to see if the fenceis at 90 degrees to the table, as shown.3. If the fence is not at 90 degrees to the t

19The following directions will give the beginner a start on jointer operations. Use scrap pieces of lumber to checksettings and to get the feel of th

2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. Whenusing tools or equipment, basic

20JOINTING AN EDGEThis is the most common operation for the jointer, thesecuts are made to square an edge of a workpiece. Set theguide fence square wi

21TAPER CUTSOne of the most useful jointer operations is cutting an edge to a taper. This method can be used on a wide variety ofwork. Tapered legs of

22DIRECTION OF GRAINAvoid feeding work into the jointer against the grain asshown in Fig. 46. The result will be chipped andsplintered edges. Feed wit

23REMOVING, REPLACING, ANDRESETTING KNIVESIf the knives are removed from the cutterhead for re-placement or sharpening, care must be used inremoving,

2412. Lower the infeed table and place a straight edge (J)Fig. 53, on the outfeed table extending over thecutterhead as shown.13. Rotate the cutterhea

25PUSH STICKMAKE FROM 1/2" OR 3/4"WOOD OR THICKNESSLESS THAN WIDTH OFMAT’L. TO BE CUTCUT OFF HERE TOPUSH 1/4" WOODCUT OFF HERE TOPUSH 1

26NOTES

27PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

3Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

GENERAL SAFETY RULES1. FOR YOUR OWN SAFETY, READ THE INSTRUCTIONMANUAL BEFORE OPERATING THE MACHINE.Learning the machine’s application, limitations, a

5ADDITIONAL SAFETY RULES FOR JOINTERS1. DO NOT OPERATE THIS MACHINE until it iscompletely assembled and installed according to theinstructions. A mach

6A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

7FUNCTIONAL DESCRIPTIONFOREWORDDelta Model 37-365X, 37-680 and 37-680Xare 8" precision jointers with a cutting capacity of 8" (203mm) width,

8CARTON CONTENTSFig. 21. Jointer2. Rabbeting Ledge3. Motor Pulley4. Fence5. Cutterhead Guard6. Fence Carriage Assembly1234567891011127. Fence Tilting

9Fig. 31. Stand, Motor, and Electricals2. Belt3. Cutterhead Pulley/Belt Guard4. Push Blocks (2)5. 1/4-20x5/8" Hex Head Screw (2)1234567896. 1/4&q