Delta 34-814 Manuel d'instructions Page 1

INSTRUCTION MANUALUNISAW®10" Right Tilting Arbor Saw(Models 34-801, 34-806, 34-814, 36-812) PART NO. 422-04-651-0064 (01-15-02)Copyright © 2002 D

10Fig. 16 Fig. 17Fig. 19ADBFAJFig. 18Fig. 20 Fig. 214. If an adjustment is necessary, loosen two screws (F)Fig. 17, and adjust splitter bracket (A) un

11Fig. 22Fig. 23Fig. 25Fig. 24Fig. 26 Fig. 27APBXZY8. Assemble upper splitter bracket (M) Fig. 22, to lowerbracket (L) using a 5/16-18x1" hex hea

12Fig. 28Fig. 30EFig. 29FASTENING MOTOR CORD TO SAW FRAME1. IMPORTANT: Turn the blade tilting handwheelcounterclockwise as far as it will go until the

13Fig. 35Fig. 36ASSEMBLING RIP FENCE HOLDER BRACKETSAssemble the rip fence holder brackets (A) and (B) Fig.37, to the four holes located in the left h

14OPERATING CONTROLS AND UNISAW ADJUSTMENTSSTARTING AND STOPPING THE SAWTo start the machine, push “ON” button (A) Fig. 39. Tostop the machine, push “

15ADJUSTING 90 AND 45DEGREE POSITIVE STOPSPositive stops are provided to quickly and accuratelyposition the blade at 90 and 45 degrees to the table. T

16ADJUSTING TABLE INSERTPlace a straight edge (B) across the table at both ends ofthe table insert as shown in Fig. 46. The table insert (A)should alw

17MAINTENANCECHANGING THE SAW BLADE1. DISCONNECT MACHINE FROM POWER SOURCE.2. NOTE: Two wrenches are supplied with the saw forchanging the saw blade;

18PROTECTING CAST IRON TABLE FROM RUSTTo clean and protect cast iron tables from rust, you will need the following materials: 1 pushblock from a joint

19Fig. 56AFig. 57BFig. 58USING THE FENCE AS ACUT-OFF GAGEWARNING: WHEN USING YOUR UNIFENCE AS ACUT-OFF GAGE, MAKE SURE IT IS PROPERLY SETUP AS DESCRIB

2GENERAL SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain ha

20Fig. 61USING AUXILIARY WOOD FACING ON BIESEMEYERRIP FENCEIt is necessary when performing special operations suchas moulding to add wood facing (A) F

21Fig. 65Fig. 66GHWIMPORTANT: For certain cutting operations such asdadoing and moulding where you are not cuttingcompletely through the workpiece, th

22Fig. 69Fig. 70Fig. 71ABCUSING ACCESSORY DADO HEADIMPORTANT: THE BLADE GUARD AND SPLITTERASSEMBLY CANNOT BE USED WHEN DADOING ORMOULDING AND MUST BE

23CONSTRUCTING A FEATHERBOARDFig. 74, illustrates dimensions for making a typical featherboard. The material which the featherboard is constructedof,

24PUSH STICKMAKE FROM 1/2" OR 3/4"WOOD OR THICKNESSLESS THAN WIDTH OFMAT’L. TO BE CUTCUT OFF HERE TOPUSH 1/4" WOODCUT OFF HERE TOPUSH 1

25BLADE GUARD ACCESSORIESDeluxe Uniguard®Blade GuardThe Delta Model 34-976 Uniguard Blade Guard withSplitter and Anti-kickback Fingers Fig. 77, is ana

26Two Year Limited WarrantyDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which

27NOTES

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): BAMMER®,INNOVATION THAT WORKS®, JETST

3ADDITIONAL SAFETY RULES FORCIRCULAR SAWSWARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURYSAVE THESE INSTRUCTIONS. Refer to

4POWER CONNECTIONSA separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected

5Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord whichhas a 3-prong grounding type plug

6OPERATING INSTRUCTIONSFOREWORDThe Delta Unisaw is a 10" right tilting arbor saw. The Delta Unisaw features set the standards in the table saw in

7ASSEMBLY INSTRUCTIONSWARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE SAW TO THE POWER SOURCE UNTIL THESAW IS COMPLETELY ASSEMBLED AND YOU UNDERSTAND

8ASSEMBLING LVC STARTERBOX TO CABINETIf you purchased the machine with magnetic pushbutton electrical controls, the saw is shipped with thestarter box

9ASSEMBLING GPE ON/OFFSWITCH1. The GPE on/off switch (A) Fig. 11, is shippedattached to a mounting bracket at the right side of themachine.2. Loosely