Delta 34-814 Manuel d'instructions Page 5
- Page / 28
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which
has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an
extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause
a drop in line voltage, resulting in loss of power and overheating. Fig. D, shows the correct gauge to use depending
on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
EXTENSION CORDS
Fig. D
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere Total Length Gauge of
Rating Volts of Cord in Feet Extension Cord
0-6 240
up to
50 18 AWG
0-6 240 50-100 16 AWG
0-6 240 100-200 16 AWG
0-6 240 200-300 14 AWG
6-10 240
up to
50 18 AWG
6-10 240 50-100 16 AWG
6-10 240 100-200 14 AWG
6-10 240 200-300 12 AWG
10-12 240
up to
50 16 AWG
10-12 240 50-100 16 AWG
10-12 240 100-200 14 AWG
10-12 240 200-300 12 AWG
12-16 240
up to
50 14 AWG
12-16 240 50-100 12 AWG
12-16 240
GREATER THAN 100 FEET NOT RECOMMENDED
FIVE HORSEPOWER MOTORS
The motors supplied with single phase, 5 horsepower Unisaws are designed to be operated from a 220-240 volt power
system.
The 5 horsepower Unisaws are not supplied with a power cord. They must be permanently connected to the building
electrical system and grounded according to the National Electrical Code. Since they are permanently connected to
the building electrical system, extension cords cannot be used with the 5 horsepower Unisaw.
THREE PHASE OPERATION
Three phase Unisaws are not supplied with a power cord. They must be permanently connected to the building
electrical system and grounded according to the National Electrical Code. Since they must be permanently connected
to the building electrical system, extension cords cannot be used with three phase Unisaws.
MAGNETIC PUSH BUTTON CONTROLS
If you purchased the Unisaw with a magnetic starter, transformer and overload protection (LVC), refer to the separate
electrical instruction manual supplied with the machine.
- INSTRUCTION MANUAL 1
- GENERAL SAFETY RULES 2
- SAVE THESE INSTRUCTIONS 3
- Refer to them often 3
- POWER CONNECTIONS 4
- MOTOR SPECIFICATIONS 4
- GROUNDING INSTRUCTIONS 4
- FIVE HORSEPOWER MOTORS 5
- THREE PHASE OPERATION 5
- MAGNETIC PUSH BUTTON CONTROLS 5
- OPERATING INSTRUCTIONS 6
- ASSEMBLY INSTRUCTIONS 7
- ASSEMBLING LVC STARTER 8
- BOX TO CABINET 8
- ASSEMBLING LVC ON/OFF 8
- ASSEMBLING GPE ON/OFF 9
- ASSEMBLING BLADE 9
- GUARD AND SPLITTER 9
- ASSEMBLY 9
- FASTENING MOTOR CORD 12
- TO SAW FRAME 12
- OPERATING CONTROLS 14
- AND UNISAW ADJUSTMENTS 14
- ADJUSTING 90 AND 45 15
- DEGREE POSITIVE STOPS 15
- ADJUSTING TABLE 15
- MITER GAGE OPERATION 16
- AND ADJUSTMENT 16
- ADJUSTING TABLE INSERT 16
- MAINTENANCE 17
- OPERATIONS 18
- USING THE FENCE AS A 19
- CUT-OFF GAGE 19
- ALWAYS INSTALL BLADE GUARD 21
- AFTER OPERATION IS COMPETE 21
- USING ACCESSORY 22
- DADO HEAD 22
- CONSTRUCTING A FEATHERBOARD 23
- PUSH STICK 24
- BLADE GUARD ACCESSORIES 25
- Two Year Limited Warranty 26
- • DELTA SERVICE CENTERS 28
- • DELTA) 28
Produits connexes et manuels pour Scies circulaires Delta 34-814
(20 pages)
(28 pages)GEAR4 AlarmDock Halo 2 manuali
Manuali dei proprietari e guide per l'utente per Docking Station GEAR4 AlarmDock Halo 2.
We fornisce 1 manuali pdf GEAR4 AlarmDock Halo 2 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commentaires sur ces manuels