Delta D25886 Manuel d'utilisateur Page 225
- Page / 339
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4. Motion Control Instructions
4-184 DVP-MC operating manual
4.8.3.6 G3: Anticlockwise circular /helical interpolation
¾ Function explanation:
Circular interpolation: The cutter conducts the cutting of the processed object in the anticlockwise
direction at the feed speed given by parameter F on the circular arc with the fixed radius or the fixed
center of a circle of the specified plane.
Helical interpolation: The cutter moves in the anticlockwise direction on the circular arc of the specified
plane，which is circular interpolation and simultaneously moves in the vertical direction of the specified
plane at the feed speed given by parameter F, which is linear interpolation.
¾ Format:
Format1: N_G3 X_Y_Z_A_B_C_P_Q_I_J_(I_K_/J_K_)T_ E_E_F_
Format2: N_G3 X_Y_Z_A_B_C_P_Q_R_T_ E_E_F_
¾ Parameter explanation:
N_: The row number of G code in NC program
X_Y_Z_: Specify the terminal positions of axis X, Y and Z corresponding to the terminal point of circular
arc; Unit: unit, data type: REAL.
A_B_C_P_Q_: Specify the terminal positions of added axes, Unit: unit, data type: REAL.
I_J_: Specify the coordinate position of the center of a circle of XY plane, Unit: unit, data type: REAL.
I_K_: Specify the coordinate position of the center of a circle of XZ plane, Unit: unit, data type: REAL.
J_K_: Specify the coordinate position of the center of a circle of YZ plane, Unit: unit, data type: REAL.
T_: Specify the quantity of one full circle, Unit: circle, data type: UINT.
E_: Specify the acceleration and deceleration of the cutter. The positive number refers to the
acceleration; the negative number refers to the deceleration, Unit: unit/second2, data type: REAL.
F: Specify the feed speed of the cutter, Unit: unit/second, data type: REAL.
¾ Instruction explanation:
Two axes among axis X, Y and Z make the circular interpolation on the plane specified by
G17/G18/G19. The 3rd axis specifies the plane to make the linear interpolation vertically.
The added axis A, B, C, P and Q make the linear interpolation. The linear interpolation and circular
interpolation and start up or stop simultaneously.
Both of E and F can be omitted. If there is only one row of code in the CNC programming area and
E, F are omitted, the velocity, acceleration, deceleration are decided by the parameters of X axis,
i.e. “maximum velocity”, “maximum acceleration”, “maximum deceleration” in the
parameters of X axis.
- DVP-MC Bus-Type 1
- Multi-Axis Motion Controller 1
- Operating Manual 1
- Content 2
- Overview of DVP10MC11T 7
- 2. System Function 10
- 3. System Installation 34
- 4.1. Instruction Table 42
- 4.2. Axis Status 46
- 4.3. Instruction Usage 47
- Instruction format 47
- Data type list 48
- 4.4.1. MC_MoveAbsolute 49
- Program Example (1) 52
- Program Example (2) 53
- 4.4.2. MC_MoveRelative 55
- 4.4.3. MC_MoveAdditive 59
- 4.4.4. MC_MoveSuperImposed 63
- 4.4.5. MC_MoveVelocity 68
- 4.4.6. MC_Stop 71
- 4.4.7. MC_PassiveHome 74
- Example 75
- 4.4.8. MC_Power 77
- 4.4.9. MC_Reset 78
- Exmaple: 79
- 4.4.10. MC_ReadStatus 80
- 4.4.12. MC_ReadAxisError 82
- 4.4.13. DMC_ReadParameter 83
- 4.4.14. DMC_WriteParameter 84
- 4.4.15. DMC_SetTorque 85
- Program Example 86
- 4.5.1. MC_CamTableSelect 87
- 4.5.2. MC_CamIn 88
- = 0, slave position is 101
- 0, slave offset = 0 102
- Master Positio 102
- offset = 40, slave position 103
- Electronic cam example: 104
- Position 105
- 4.5.3. MC_CamOut 107
- Program Example: 108
- 4.5.4. DMC_CamSet 110
- Acceleration 112
- 4.5.5. MC_GearIn 114
- . UINT D 115
- 4.5.7. MC_Phasing 118
- Sequence Diagram 120
- 4.5.8. DMC_CapturePosition 121
- 4.5.9. DMC_VirtualAxis 127
- 4.5.10. DMC_ExternalMaster 129
- 4.6. Logical Instruction 131
- 4.6.3. ADD_R 132
- 4.6.4. SUB 132
- 4.6.5. SUB_DI 133
- 4.6.6. SUB_R 133
- 4.6.7. MUL 134
- 4.6.8. MUL_DI 134
- 4.6.9. MUL_R 135
- 4.6.10. DIV 135
- 4.6.11. DIV_DI 136
- 4.6.12. DIV_R 136
- 4.6.13. AND 137
- 4.6.14. OR 137
- 4.6.15. XOR 138
- 4.6.16. NOT 138
- 4.6.17. CTU 139
- Program example: 140
- 4.6.18. CTD 141
- 4.6.19. CTUD 143
- 4.6.20. TON_s 145
- 4.6.21. TOF_s 147
- 4.6.22. TONR_s 149
- 4.6.23. TON_ms 151
- 4.6.24. TOF_ms 152
- 4.6.25. TONR_ms 153
- 4.6.26. CMP 154
- 4.6.27. CMP_DI 155
- 4.6.28. CMP_R 156
- 4.6.30. MOV_DI 158
- 4.6.31. MOV_R 158
- 4.6.34. MOVF_R 161
- Program example : 162
- 4.6.36. MOV_BW 163
- 4.6.38. ZCP 165
- 4.6.39. ZCP_DI 166
- 4.6.40. ZCP_R 167
- 168
- 4.6.43. OUT 169
- 4.6.44. R_Trig 169
- 4.6.46. ZRSTM 172
- 4.6.47. ZRSTD 173
- 4.6.48. SQRT_R 174
- 4.6.49. MOD 174
- 4.6.50. MOD_DI 175
- 4.6.51. MOD_R 175
- 4.6.52. Real_To_Int 176
- 4.6.53. Real_To_DInt 176
- 4.6.54. Int_To_Real 177
- 4.6.55. DInt_To_Real 177
- Example 1: 178
- Example 2: 179
- Example 3: 179
- 4.6.58. Offset _R 182
- 4.7. Application Instruction 183
- 4.7.2. Rotary Cut Parameters 184
- Short material cutting 185
- Equal length cutting 185
- The entry curve 187
- The end curve 188
- 4.7.5.1 189
- 4.7.5.2. APF_RotaryCut_In 191
- 4.7.5.3. APF_RotaryCut_Out 192
- Explanation of areas 197
- Steps for flying shear 197
- Function feature 197
- Shear axis 198
- Sync area 203
- 4.8.1. G Code Input Format 206
- Center of a circle 222
- Start point 222
- Terminal point 222
- （）200,200 223
- Start point Start point 226
- Instruction example 1: 232
- Instruction example 2: 232
- Instruction example: 232
- 4.8.4. DMC_NC 233
- Program example 1: 235
- Program example 2: 236
- ¾ Program: 237
- ¾ Steps: 237
- 5.Troubleshooting 258
- 5. Troubleshooting 259
- Appendix A 264
- Appendix B 287
- Appendix C 301
- Appendix D 333
- Appendix E 338
Produits connexes et manuels pour Compresseurs d'air Delta D25886
(72 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.703 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels